124 lines
3.0 KiB
Plaintext
124 lines
3.0 KiB
Plaintext
[bogus section]
|
|
|
|
This section is not used by PRTE code. But we have to put a RST
|
|
section title in this file somewhere, or Sphinx gets unhappy. So we
|
|
put it in a section that is ignored by PRTE code.
|
|
|
|
|
|
Hello, world
|
|
============
|
|
|
|
[stacktrace signal override]
|
|
|
|
PRTE was inserting a signal handler for signal %d but noticed that
|
|
there is already a non-default handler installed. PRTE's handler was
|
|
therefore not installed; your job will continue. This warning message
|
|
will only be displayed once, even if PRTE encounters this situation
|
|
again.
|
|
|
|
To avoid displaying this warning message, you can either not install
|
|
the error handler for signal %d or you can have PRTE not try to
|
|
install its own signal handler for this signal by setting the
|
|
"prte_signals" MCA parameter.
|
|
|
|
Signal: %d
|
|
Current prte_signal value: %s
|
|
|
|
[stacktrace bad signal]
|
|
|
|
PRTE was inserting a signal handler but was given an invalid signal
|
|
number:
|
|
|
|
Signal string: %s
|
|
Bad value: %s
|
|
|
|
The given value must be an integer within the signal number range.
|
|
Please correct the value and try again.
|
|
|
|
[malformed net_private_ipv4]
|
|
|
|
PRTE has detected at least one malformed IP address or netmask in the
|
|
value of the prte_net_private_ipv4 MCA parameter. The
|
|
prte_net_private_ipv4 MCA parameter accepts a semicolon-delimited list
|
|
of Classless Inter-Domain Routing (CIDR) notation specifications, each
|
|
of the form <ipaddress>/<mask>. For example:
|
|
|
|
10.0.0.0/8;172.16.0.0/12;192.168.0.0/16;169.254.0.0/16
|
|
|
|
The first detected malformed entry was %s.
|
|
|
|
[invalid-net-mask]
|
|
|
|
PRTE has detected a malformed IPv4 address or netmask:
|
|
|
|
Value provided: %s
|
|
|
|
Accepted values follow the Classless Inter-Domain Routing (CIDR)
|
|
notation specifications. For example:
|
|
|
|
10.0.0.0/8
|
|
172.16/12
|
|
192.168
|
|
169.254.0.0/16
|
|
|
|
[malformed-uri]
|
|
|
|
PRTE has detected a malformed URI:
|
|
|
|
URI: %s
|
|
|
|
Accepted values follow IETF RFC3986, e.g.
|
|
"file://192.168.1.1/over/there"
|
|
|
|
[relative-path]
|
|
|
|
When creating a URI, all files must be specified in absolute paths:
|
|
|
|
Value provided: %s
|
|
|
|
Please update your application to provide the full path to the file.
|
|
|
|
[sys-limit-failed]
|
|
|
|
Per request, PRTE attempted to set a system resource limit to a given
|
|
value:
|
|
|
|
Resource: %s
|
|
Limit: %s
|
|
|
|
The system has refused to allow this operation. This is likely due to
|
|
a permission limitation, or specifying an unsupported value. Please
|
|
check the system or remove the request and try again.
|
|
|
|
[sys-limit-unrecognized]
|
|
|
|
PRTE received a request to set a system resource limit. Sadly, OMPI
|
|
does not recognize or currently support the specified resource:
|
|
|
|
Resource: %s
|
|
Limit: %s
|
|
|
|
Please correct the request and try again.
|
|
|
|
[dir-mode]
|
|
|
|
While working through a directory tree, we were unable to set a
|
|
directory to the desired mode:
|
|
|
|
Directory: %s
|
|
Mode: %0x
|
|
Error: %s
|
|
|
|
Please check to ensure you have adequate permissions to perform the
|
|
desired operation.
|
|
|
|
[mkdir-failed]
|
|
|
|
A call to mkdir was unable to create the desired directory:
|
|
|
|
Directory: %s
|
|
Error: %s
|
|
|
|
Please check to ensure you have adequate permissions to perform the
|
|
desired operation.
|